Mytee Lite 2 set up

Hey everyone Paul from IT products here I'm going to go over with you on the set up on the mighty light tube model 870 you're probably excited to use it.

Let's see how it sets up first off when you pull out of the box you're going to find a couple little things number one to stop something talks about registering the product very simple just go to my t-dot-com backslash call we've made the manual as simple as possible.

Go ahead and take a look at your manual if you get a chance now.

We've taken out the box let's go over some of the features one of the first things you're going to notice as it comes with the handle handle has a lot of nice features it's got a basket or holding chemical rags spray bottles also has rings for cord wrap and it's also got these four holes let's see how these four holes match up to the machine to the commander.

Mytee Lite 2 set up

Here's a for instance on the back of the unit and if they correspond with the four holes on the tube now your handle comes with the hardware it's a bolt split lock washer and a washer.

Let's go to put that on and for right now we're just going to make it finger tight now make a u-bolt on finger tight we're going to use a 7/16 wrench socket crescent wrench I've opted for the Handy ratchet.

Now we've got our handling on it let's take a closer look at the tanks the mighty limit 8070 comes three gallon vacuum tank and a three gallon solution tank now let's look at how to access the solution tank first off you've got to take off the backup thing to remove the backing tank simply undo the latch on the back lift up from the back and then lift off your tank and there's your vanity now you'll notice on the solution tank large opening now that's important because it makes it very simple to fill even using a five-gallon bucket now there's a couple ways you can use your solution you can either premix your chemical put in your solution tank or you can pre spray the fire builders on the carpet or the match of the upholstery and then is put fresh water in your solution tank.

After we put our solution in the tank let's go to put our bathroom tank back on look at the secret to putting your tank back on the secret putting your vacuum tank back on its to do the opposite what we've just done we'll start by putting the front end first we put the latch back in place clamp it down and snap it into place now another feature you'll find in the box or your hoses let's take a closer look.

Now let's work with our 15 foot back and solution hose first step is we're going to want to hook up the machine side first.

We're going to work with the male Kitty and. This is the female beauty on machine.

The secret to putting quick disconnects on is the ring on the female we always want to be able to pull that back.

Let's pull the ring back slide the nail in and then snap it in then we want to take our vinyl cuff put it onto our backing tape the other feature that comes with the mighty light is a stainless steel three-and-a-half inch with whole street school.

Let the bat onto our hose now the same concept we pull the ring back on the female slide the male and snap it into place the back in goes slides right on people now they've got our eldest set up let's take a closer look at the wheels another feature that makes the mighty light top in its class and one of the best upholstery and spotting machines around is the size of the wheels four inch wheels and two inch casters that means it might like can roll very easily and the unique thing about the two inch casters is their locking casters.

Once you get it set into place simply lock the cast in place and then you don't worry about the Machine rolling nothing that's closer look at the swiftness we're going to know you've got three switches here and they're marked vacuum pump Heat let's take a closer look at which each one of those needs and the vacuum that just sucks the debris and pulls the debris out of the pipe the pump is what sprays a solution into the fiber now our here's a thousand watt heater that means it can heat up the solution in just a matter of minutes.

Now we've seen the features that are on this unit let's put it to work alright.

We're outside now got our mighty light all set up and we've added a little bit of solution but just to demonstrate how big the opening on a solution tank really is we're going to go ahead and add a little more fluid to it you want to be careful not to overfill it maybe stop about an inch from the top alright now that we've got our solution in the solution tank we want to turn our switches on first we're going to turn our pump then we're going to turn on our heater we always want to do it in that order first the pump then the heater now let me show you an easy tip to getting your heater nice and hot.

Now that you have the pump and the heater both turned on want to give the heater just a few minutes to heat up after that make your bolster tool aim it back into the solution tank and spray this will allow the water to flow through the solution hose getting that cold water out sending it back into the solution tank and giving that heater time to push some hot water into the solution hose you'll know when it's hot have to feel after that just give it another minute or.

For the heater to catch back up with itself and then you're ready to go alright now we've got our pump time we've got our heaters all warmed up let's put our vacuum tank back on you and then we put our vacuum hose back on their back now some of the chemical you may use may suds up and that could damage the back motor.

You want to be careful best thing you can do is add a little diploma to your vacuum tank and that will kill the foam here's how you do it simply take off the lid on your back from tank add a little deep bomer cure back to take that's all there is to it d foam was very common you can get at any janitorial supply store or any chemical house alright we've got our pump Prime our heaters are hot we've add a little deep foam into the vacuum tank now let's go ahead and turn our vacuum motors on to switch the pump slits and the heater switch are already on and here's our vacuum now the vacuums are on let's get to work all rights are ready to go and remember the mighty light is great for upholstery carpet mats for the purpose of this demonstration we've got a mat.

Let's see how it works you can see with the vacuum and the pump and the heater on the unit's really doing a lot of the work all we have to do is squeeze the trigger and pull the upholstery tool back it'll spray hot solution into the mat and vacuum it back up then we'll make a dry stroke back up and then we'll offset and do another one another pass you can see the steam coming from the upholstery we've got a solution nice and hot it's reacting good with our chemical always remember to make a dry stroke pass.

That's a mighty light 80 70 it's easy to set up it's easy to use and you're going to be happy with the results.

YT Stats Views: 0 Likes: 0 Dislikes: 0